Knowing Essential Plumbing Skills is Important For Installing a Bathtub
Knowing Essential Plumbing Skills is Important For Installing a Bathtub
Blog Article
The content below in relation to Tools You Need to Install a New Bathtub is immensely insightful. Don't overlook it.
Setting up a tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a new one is also a reasonably difficult task. If the old tub is conveniently obtainable, the project can relocate rapidly; if you have to open a wall to get rid of the old tub and also place the brand-new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require an assistant to vacate the old tub and also set in the brand-new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to working with a professional to take over a halfway-completed job, it is far better to think about utilizing one prior to you begin. Chances are you may require a professional plumber to make tube links.
This article will assist you set up a brand-new bath tub in your washroom if you have currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water system pipes.
Your devices and product checklist need to comprise the following:
Getting ready for the Installation
First of all, the supporting framework provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of removing the existing taps can be rather bothersome because of the limited gain access to that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wooden boards under its feet, put the bathtub in the needed setting. The wood boards are helpful in equally spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the level reads level.
To install taps, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water system and also check all joints as well as new pipework for leaks as well as tighten them if required. Fill up the bath tub and also inspect the overflow outlet and also the normal electrical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bathtub needs to wait till the bathtub has actually been utilized at least when as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end gives a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers are in place between the faucet as well as the sink. Protect the tap in position with the manufacturer provided backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The previous type should be attached to the tap ends first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing issues with wetness and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to permit the movement experienced when the tub is in use. The sealer can break relatively early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on How to Install a Bathtub Yourself, I thought sharing that blog post was really helpful. Liked our blog entry? Please share it. Help somebody else check it out. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
This Resource Report this page